The BCM®™'s Grip (GFG) featuresReduced angle for improved ergonomics and trigger controlHinged trap door offering storage inside the grip with a water resistant rubber gasketEach grip features an extended forward tang to close the gap between the trigger guard and pistol grip, and a high rise "beavertail" style back strap.Up to a quarter of an inch wider than the BCM® Mod 0 and Mod 1 grips.Made in the USA and manufactured from high quality impact resistant polymers.Each grip test fit to ensure proper function (may display attributes consistent with this QC process) 

Kinesthetic Angled Grip - KAGThe KAG is the end result of collaboration between BCM® and Travis Haley, founder of Haley Strategic Partners and inventor of multiple weapons manipulation enhancements in the firearms industry.Designed to complement modern shooting grips, the Kinesthetic Angled Grip (KAG) uses a biomechanically efficient forward rake to create an interface for positive retention and joint relief to the wrist, elbow, and shoulder, allowing for smooth weapon manipulation without substantial increase to the girth of the weapon system. Textured on both front and back, the profile of the KAG creates a channel for consistent and positive engagement which translates directly into improved efficiency in weapons manipulation and target to target transitions. Forward rake gives positive retention when using "C-clamp" (thumb over bore) method of handguard supportWorks as a rest for supported firing positionsSlight angle without significant bulk adds just the right amount of relief to the wrist without substantially increasing the girth of the handguardSmall profile is just enough to get repeatable hand position on weapon forendTextured in front and back for positive engagementMade in the U.S.A. from high quality, impact resistant polymers. 

KAG-MCMR (M-LOK® Compatible*)Kinesthetic Angled Grip - KAGThe KAG is the end result of collaboration between BCM® and Travis Haley, founder of Haley Strategic Partners and inventor of multiple weapons manipulation enhancements in the firearms industry.Designed to complement modern shooting grips, the Kinesthetic Angled Grip (KAG) uses a biomechanically efficient forward rake to create an interface for positive retention and joint relief to the wrist, elbow, and shoulder, allowing for smooth weapon manipulation without substantial increase to the girth of the weapon system. Textured on both front and back, the profile of the KAG creates a channel for consistent and positive engagement which translates directly into improved efficiency in weapons manipulation and target to target transitions. Forward rake gives positive retention when using "C-clamp" (thumb over bore) method of handguard supportWorks as a rest for supported firing positionsSlight angle without significant bulk adds just the right amount of relief to the wrist without substantially increasing the girth of the handguardSmall profile is just enough to get repeatable hand position on weapon forendTextured in front and back for positive engagementMade in the U.S.A. from high quality, impact resistant polymers.

BCM®™ Vertical Grip Mod 3 (M-LOK® Compatible*)Direct Attach VersionLow-profile length for increased mobility and decreased snag factor.The forward angle increases the rigidity of the forearm, while providing a more natural wrist angle.Can be mounted in reverse angle to increase control when grabbing handguard and grip.Flat sides with aggressive texture give better yaw control to the shooter during firing and non-firing manipulations.A lightweight design at 1.9 ounces.Made in the U.S.A., manufactured from high quality, impact resistant polymers.

BCM®™ VG-1913-Mod-3 The new (United States Patent 9,709,358) BCM® Direct Mount Picatinny 1913 interface system, was developed to be the most rigid, light-weight, and cost effective system available for Vertical Pistol Grips and Hand Stop type accessories.Most of the industry relies on a simple screw and backing nut for a mounting system. BCM has developed a patent pending anchor system that not only secures to the mounting surface, but spreads the energy and force throughout the accessory. Conventional mounting systems can allow for an increased amount of shifting and flexing of the accessory. The BCM direct mount interface system reduces those issues and offers a more secure lockup, eliminating play in the mounting surface. Direct Attach Picatinny 1913 Rail VersionLow-profile length for increased mobility and decreased "snag" factor.The forward angle increases the rigidity of the forearm, while providing a more natural wrist angle.Can be mounted in reverse angle to increase control when grabbing handguard and grip.Flat sides with aggressive texture give better yaw control to the shooter during firing and non-firing manipulations.Anchor and bolt system offers a simple robust design, while maintaining a lightweight 1.9 ounces. United States Patent 9,709,358Made in the U.S.A., manufactured from high quality, impact resistant polymers. Tools needed: T15 Torx Driver (not supplied)Insert tool (T15 Torx™ driver) into the screw from under the BCM 1913 Vertical GripPush tool into the screw to extend the Picatinny anchor, making it protrude from the top.With the Picatinny anchor protruding, slide the BCM Vertical Grip onto the Picatinny rail until positioned in the desired location. Grip can be installed in your desired orientation, angled forward or back.Push the BCM Vertical Grip against rail, engaging the BCM Vertical Grip's recoil lug to the intersecting Picatinny rail grooves.With the recoil lugs engaged, tighten the screw to snug the anchor (approximately 18-20 Inch-lbs. plus quarter turn).Ensure there is no wiggle or forward/backward movement once tight.*Blue thread locker may be used on threaded fasteners

BCM®™ VG-1913-Mod-3 The new Patent Pending BCM® Direct Mount Picatinny 1913 interface system, was developed to be the most rigid, light-weight, and cost effective system available for Vertical Pistol Grips and Hand Stop type accessories.Most of the industry relies on a simple screw and backing nut for a mounting system. BCM has developed a patent pending anchor system that not only secures to the mounting surface, but spreads the energy and force throughout the accessory. Conventional mounting systems can allow for an increased amount of shifting and flexing of the accessory. The BCM direct mount interface system reduces those issues and offers a more secure lockup, eliminating play in the mounting surface. Direct Attach Picatinny 1913 Rail VersionLow-profile length for increased mobility and decreased snag factor.The forward angle increases the rigidity of the forearm, while providing a more natural wrist angle.Can be mounted in reverse angle to increase control when grabbing handguard and grip.Flat sides with aggressive texture give better yaw control to the shooter during firing and non-firing manipulations.Anchor and bolt system offers a simple robust design, while maintaining a lightweight 1.9 ounces.Made in the U.S.A., manufactured from high quality, impact resistant polymers. Tools needed: T15 Torx Driver (not supplied)Insert tool (T15 Torx driver) into the screw from under the BCM 1913 Vertical GripPush tool into the screw to extend the Picatinny anchor, making it protrude from the top.With the Picatinny anchor protruding, slide the BCM Vertical Grip onto the Picatinny rail until positioned in the desired location. Grip can be installed in your desired orientation, angled forward or back.Push the BCM Vertical Grip against rail, engaging the BCM Vertical Grip's recoil lug to the intersecting Picatinny rail grooves.With the recoil lugs engaged, tighten the screw to snug the anchor (approximately 18-20 Inch-lbs. plus quarter turn).Ensure there is no wiggle or forward/backward movement once tight.*Blue thread locker may be used on threaded fasteners

The XTM Enhanced Rail Panels are low-profile, two-piece covers that attach anywhere on a 1913 Picatinny rail without having to remove previously mounted accessories. Replacing the original XTM Panels, the Enhanced XTM Panels feature an aggressive anti-slip texture and dual-side routing clips for retention of light/laser cables.The design and reinforced material construction ensure the panels will remain in place under all operating conditions, but allow for easy removal using the tips of two rounds when necessary. Each set comes with four (4) two-piece panels which will cover ONE side of a carbine rail.Made in the USA.NSN: MAG510-BLK 1005-01-619-8865Technical SpecificationsMore InformationAttachment 1913 Picatinny RailsPlatform AR15, M4, M16

The MIAD (Mission Adaptable) GEN 1.1 Grip is a drop-in replacement for the standard AR15 / AR10 grip, now available in two dedicated configurations to fit most receivers. It is designed to improve ergonomics with interchangeable front and rear straps for personalized hand fit, an aggressive texture for positive weapon control, and is compatible with all Magpul grip cores to adapt to various storage needs. This update to the original MIAD has improved strap retention and also comes standard with the newest grip core that holds an included 1/2 oz. lubrication bottle.Two sizes are available. This TYPE 2 Kit (MAG521) uses taller back-straps for optimized fit with certain 7.62x51 receivers*. The TYPE 1 Kit (MAG520) is compatible with most AR15 / M4s, as well as AR10-type receivers utilizing that standard. All mounting hardware is included.Made in the USA.Technical SpecificationsMore InformationPlatform AR10, AR15, M4, M16, M110, SR25Grip Angle 25 degreeHeight, receiver to bottom 4.0 in.Thickness, max 1.2 in.Other Specs * NOTE: This TYPE 2 Kit uses taller backstraps for optimized fit with certain 7.62x51 receivers such as the Armalite AR-10A/B/T, DPMS LR308, KAC SR25, LaRue OBR, LMT .308 MWS, Palmetto PA10, and S&W M&P10.Some 7.62x51 variants such as the Aero Precision M5 308, CMMG Mk3, CORE Rifle Systems CORE30, HK 417/MR762A1, LWRCI REPR, Mega Arms MATEN, POF P-308, Ruger SR-762, and SIG716 will require the TYPE 1 Kit.In general, the TYPE 1 Kit will fit most all 7.62x51 AR lower receivers but there may or may not be a gap between the backstrap's 'beavertail' and the receiver. This gap is purely aesthetic and will not affect function.